Another vital area of understanding is how flexbox makes no assumption about the writing mode of the document. In the past, CSS was heavily weighted towards horizontal and left-to-right writing modes. Modern layout methods encompass the range of writing modes and so we no longer assume that a line of text will start at the top left of a document and run towards the right-hand side, with new lines appearing one under the other. There are also some predefined shorthand values which cover most of the use cases. You will often see these used in tutorials, and in many cases these are all you will need to use. The predefined values are as follows: If you set box-flex to 0, Firefox forces the element to act like it’s using the quirks-mode box model. To have more control over flex items we can target them directly. We do this by way of three properties: The result of this is that your items will all line up in a row, using the size of the content as their size in the main axis. If there are more items than can fit in the container, they will not wrap but will instead overflow. If some items are taller than others, all items will stretch along the full length of the cross-axis.

The two 2012 specs are roughly equivilant in terms of features, differing mainly in syntax. The earlier 2009 spec is less comprehensive though covers a lot of the same ground. The flex-wrap property is set to nowrap. This means that the flex items will always remain in a single row or column, overflowing their container if their combined width/ height exceeds the containing element width/ height.Setting flex: initial resets the item to the initial values of flexbox. This is the same as flex: 0 1 auto. In this case the value of flex-grow is 0, so items will not grow larger than their flex-basis size. The value of flex-shrink is 1, so items can shrink if they need to rather than overflowing. The value of flex-basis is auto. Items will either use any size set on the item in the main dimension, or they will get their size from the content size. Today I’m sharing the details on my new FLEX tool boxes, plus more exciting equipment. FLEX Tool Boxes & More

In both cases the start edge of the cross-axis is at the top of the flex container and the end edge at the bottom, as both languages have a horizontal writing mode. Using flex: auto is the same as using flex: 1 1 auto; everything is as with flex:initial but in this case the items can grow and fill the container as well as shrink if required. If we have three 100 pixel-wide items in a container which is 500 pixels wide, then the space we need to lay out our items is 300 pixels. This leaves 200 pixels of available space. If we don't change the initial values then flexbox will put that space after the last item. If the flex-direction is row and I am working in English, then the start edge of the main axis will be on the left, the end edge on the right. The justify-content property is used to align the items on the main axis, the direction in which flex-direction has set the flow. The initial value is flex-start which will line the items up at the start edge of the container, but you could also set the value to flex-end to line them up at the end, or center to line them up in the center.To cause wrapping behavior add the property flex-wrap with a value of wrap. Now, should your items be too large to all display in one line, they will wrap onto another line. The live sample below contains items that have been given a width, the total width of the items being too wide for the flex container. As flex-wrap is set to wrap, the items wrap. Set it to nowrap, which is also the initial value, and they will instead shrink to fit the container because they are using initial flexbox values that allows items to shrink. Using nowrap would cause an overflow if the items were not able to shrink, or could not shrink small enough to fit. Before we can make sense of these properties we need to consider the concept of available space. What we are doing when we change the value of these flex properties is to change the way that available space is distributed amongst our items. This concept of available space is also important when we come to look at aligning items. While flexbox is a one dimensional model, it is possible to cause our flex items to wrap onto multiple lines. In doing so, you should consider each line as a new flex container. Any space distribution will happen across that line, without reference to the lines on either side. The shorthand you often see in tutorials is flex: 1 or flex: 2 and so on. This is as if you used flex: 1 1 0 or flex: 2 1 0 and so on, respectively. The items can grow and shrink from a flex-basis of 0. Features: Fold-down shelf creates discrete storage option that is great for small or crowded workshops. 70 lb. carrying capacity.