Laser 6869 Safety Locking Wire 0.8mm x 30m

Product Information

To finish the job, use the special Wire Twisting Pliers from Laser Tools (part number 2722) and the stainless steel Safety Locking Wire, also from Laser Tools — part number 6869. Since safety wire is made of a malleable alloy, it retains its shape after being bent, rather than springing back to its original shape. They are installed just like any other washer, after which the sides of the tab are bent up to make contact with the sides of the head of the fastener. The advantage of safety wire tabs is that the fastener to be secured does not need to be drilled, which can be advantageous for fasteners that should not or cannot be drilled because of size or damage concerns.

Professional lock wire for commercial or occasional use Stainless steel lock wire Twist safety wire Commonly used in motor sport and also used in the aeronautical and defence industries Wide range of uses including safety wiring of nuts, bolts, turnbuckles to prevent loss through engine vibration / movement As well as this can be used for crafts, jewellery making, tying and binding Also used to secure oil drain plugs, filters, grips and bolts etc.The wire needed is long enough to reach from a fixed location to a hole in the removable fastener, such as a pin — a clevis fastener, sometimes a linchpin or hitch-pin through a clevis yoke for instance — and the wire pulled back upon itself, parallel to its other end, then twisted, a single end inserted through a fastener, and twisted again, possibly then anchored to a second fastener or other part, then twisted once again, having excess slack pulled relatively taut to be secure. The two drilling jig kits from Gunson (part number 77080 Metric or 77118 Imperial), include both a nut jig and a bolt jig. It’s especially useful for critical areas such as suspension and brakes, but it’s also very useful for securing other components, such as keeping exhaust manifold bolts, or remote oil filter mounting bolts from becoming loose. We are also the UK and European distributor for Aircraft Spruce and Speciality, with whom we have been doing business with for over 25 years. If the fastener part to be secured does not come with a hole for the safety wire, one may need to be drilled.

Again, the end cap is too large to pass through the hole that the wire passed through, and thus the cable is secured. In addition to installing 3 times quicker than safety wire, Safe-T-Cable also produces a stronger and safer result. Although many systems purport to be more efficient than installing traditional safety wire, an advantageous by-product of the twisting method of installing safety wire is that it leaves a highly visible and easily inspectable indication that the fasteners in question are in fact properly secured.

Wire can prevent nuts from falling off, but can not prevent fatigue failure which results when low tensioned bolts are exposed to vibration. Chose from our fantastic selection of Nuts, Bolts, Caphead Bolts, Screws and Washers for your Model Airplane, Boat, Car, Train or Helicopter. The presence of safety wiring also serves as an indicator that the fasteners have been properly tightened.

The advantage to this tool is its long and thin design, which can access hard-to-reach areas where one's hands or pliers do not fit.The two ends of the wire-loop thus formed are joined by twisting them together with a tool, using enough twists to be secure, then released from the twisting tool. The cable is threaded through a hole on the fastener to be secured, which is large enough to accommodate the wire but too small for the cap on the other end of the cable to pass through it. When checking out, the correct up to date conversion will be applied by the secure gateway selected. When drilling a fastener, the choice of where to drill it depends on the type of fastener and to what it will be wired. This property allows it to remain locked around an object, such as when it is passed through a small hole on a fastener, looped back upon itself and then twisted.

Once the safety wire is properly installed, the sides of the tab transfer the force of the safety wire to the fastener, as though the fastener itself had been drilled and had the safety wire run through it. In addition we have distributorships for Aircraft Tool Supply, LP Aero Plastics, Falcon Gauge, Ceconite / Randolph and Shield Technology to name but a few! Unlike safety wire, Safe-T-Cable installations have no sharp edges, which greatly reduces the risk of injury.Witness wires also serve the purpose of providing a rapid method for ensuring critical safety equipment or systems have not been used or tampered with since their last repair, reset, or inspection, and also that the container of such equipment has not been inadvertently opened, disturbed or tampered with, therefore providing confidence in their readiness for use.